HD | HEAT DEFIANT CARE & TIPS

We recommend washing your wig every 6-8 wears

  

CLEANSE & CONDITION

  • Before washing your HD wig or hair piece, gently remove any tangles using only your Jon Renau wide tooth comb

  • Hold wig or hair piece under cool running water  

  • Gently lather the hair with a capful of Jon Renau Shampoo for all Synthetic Fibers, while making sure that the hair is traveling in the same direction. DO NOT rub hair as this may cause tangling

  • Rinse thoroughly in cool water until the water runs clear

  • Wrap wig or hairpiece in a towel and gently pat dry 

  • Gently detangle hair using your Jon Renau wide tooth comb

  • Spray with Leave-In Conditioning Spray (3-5 pumps) keeping away from base of wig or hair piece and allow to fully dry either by air-drying (Synthetic Wigs) or using Dry and Style instructions below (For HD Synthetic Wigs Only)

 

    ADDING CURL TO YOUR HD SYNTHETIC WIG

    • Heat your curling iron to 270°-280° F

    • Using your Jon Renau wide tooth comb, gently comb hair free of tangles

    • Starting at the nape, take ½ inch-1.5 inch sections of hair (Smaller sections=tighter curls, larger sections=looser curls)

    • Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section) - Heat Treat Thermal Spray is heat activated and excellent when used with flat irons, curling irons, hot and velcro rollers. This non-sticking thermal protectant and styling spray prevents hair damage by permitting a clean release from styling tools. Hair is left brushable and volumized. For use with both human hair and heat defiant synthetic hair. Heat Treat Thermal Spray is sold seperately and can be found here

    • Gather hair into curling iron, smooth through to the ends. Roll iron up towards base of wig or hairpiece, staying 1-2 inches away

    • Hold for 10-15 seconds, then turn the tip of iron toward the ground and release curl into palm of hand

    • Holding curl in one hand, gather up towards base and secure curl with a small metal clip (like a pin curl)

    • Allow curl to cool completely (about 5 minutes); remove clip and let curl hang naturally

    • Hair can be combed with your Jon Renau wide tooth comb (or fingers for best results) to blend curls

    DRYING & STYLING YOUR HD SYNTHETIC WIG

    • Air drying your wig will give the best results. You can gently blow dry (low-medium heat) using ONLY your Jon Renau wide tooth comb

    • Apply HD Smooth Detangling Spray, (3-5 pumps) focusing on the bottom half of wig or hairpiece. Gently comb through again with your Jon Renau wide tooth comb

    • We recommend that ONLY the Jon Renau wide tooth comb is used on your HD wig or hair piece. Other tools will cause frizzing/tangling

    • HD Fiber can withstand heat tools up to 350° F; However we recommend working at 270°-280° F to preserve your fibers

    • It is recommended to use professional grade heat styling tools with digital temperature settings to control heat 

     

    FLAT IRONING YOUR WIG

    • Heat your flat iron to 270°-280° F

    • Starting at the nape, take ½ inch-1.5 inch sections

    • Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)

    • Staying at least 1-2 inches away from base, slowly smooth flat iron down through ends

    • Keep hair smooth by following behind the flat iron with your Jon Renau wide tooth comb

    • Allow hair to hang naturally and cool completely 

     

    TIPS TO GET THE MOST WEAR OUT OF YOUR WIG

    • We recommend using HD Smooth Detangling Spray with a Jon Renau wide tooth comb DAILY to detangle your HD wig after wear. This is especially important with the mid-length to long length HD wigs, hair pieces or hair extensions

    • We offer HD Smooth in a convenient 2oz. size for travel

    • Allow your HD wig to air dry naturally instead of blow drying to help maintain the integrity of the fiber

    • Help protect the fiber against heat damage by using Heat Treat Thermal Spray when using heat styling tools - Sold separately